GFRP processing combines glass fibres with thermoset or thermoplastic resins using lay‑up, infusion, RTM (Resin Transfer Moulding), or pultrusion (pull-through composit process). With steel or composite tooling, it produces lightweight, corrosion‑resistant parts for automotive, marine, wind energy, and industrial applications.
Glass fibre reinforced plastic (GFRP) processing involves combining thermoset or thermoplastic resin systems with glass fibres to produce lightweight, high‑strength composite components. Common processes include hand lay‑up, spray‑up, vacuum infusion, resin transfer moulding (RTM), pultrusion, and compression molding. Glass fibres—typically E‑glass or S‑glass—are supplied as mats, woven fabrics, rovings, or preforms and are impregnated with polyester, vinyl ester, epoxy, or thermoplastic resins. Tooling requirements depend on the chosen process: open moulds made from gel‑coated composite structures are used for manual lay‑up, while closed moulds in aluminum or alloyed tool steel enable dimensional accuracy in RTM and compression moulding. Heating systems, vacuum equipment, and release agents ensure proper curing and surface quality. GFRP parts offer high stiffness‑to‑weight ratios, corrosion resistance, and design flexibility, making them widely used in automotive exterior panels, wind‑turbine blades, electrical housings, infrastructure reinforcements, sports equipment, and marine structures.
BÖHLER K340 ISODUR belongs to the group of 8% chromium steels. This tool steel is produced using the electro-slag remelting (ESR) process developed by BÖHLER. This re-melting technology ensures the lowest micro and macro segregation as well as excellent purity and uniformity of the material. Compared to conventional 12% chromium steels, BÖHLER K340 ISODUR offers significantly better toughness, hardening response and higher resistance to adhesive wear. This material is therefore used in virtually all cold work applications in situations where tool steels like 1.2379 are insufficient in terms of adhesive wear resistance and toughness. K340 ISODUR also features better machinability and reduces the risk of stress cracking during electrical discharge machining.
Read MoreBÖHLER K390 MICROCLEAN is a high-alloyed, high-performance cold work tool steel manufactured using powder metallurgy. This material has the highest alloy content in the group of cold work tool steels with high vanadium content. The high alloy content gives this material outstanding wear resistance. At the same time, the powder metallurgical manufacturing process creates a uniform matrix with finely distributed primary carbides. Among other things, this leads to good material toughness. BÖHLER K390 MICROCLEAN is a problem solver for applications requiring extremely high wear resistance and compressive strength.
Read MoreBÖHLER M310 ISOPLAST is a corrosion-resistant, martensitic chromium steel which, through electroslag remelting and optimization of the chemical composition, has a good homogeneity and a balanced hardness-toughness-corrosion resistance ratio.
Read MoreBÖHLER M390 MICROCLEAN is a corrosion-resistant, martensitic chromium steel produced by powder metallurgy. Due to its alloy design, this steel has very high wear resistance and good corrosion resistance. In addition, BÖHLER M390 MICROCLEAN is approved for food and beverage contact.
Read MoreBÖHLER N695 is a corrosion-resistant, martensitic chromium steel with a high carbon content and added molybdenum.
Read MoreUddeholm Mirrax 40 is a prehardened remelted stainless tool steel, supplied at 40 HRC. Uddeholm Mirrax 40 is produced using the electroslag remelting (ESR) process – an additional step in the steelmaking process that ensures very clean steel. Consequently, Uddeholm Mirrax 40 is capable of being polished to a very high surface finish. In addition, the combination of high hardness with high toughness results in a mould with good resistance to indentations and minimize the risk of unexpected failures, leading to a safer mould and a prolonged tool life. Benefits Lower production costs Fast tool making Excellent surface finish possible Less maintenance work Safe production
Read MoreUddeholm Tyrax ESR combines best in class toughness, corrosion and wear resistance. This grade was developed for molding of high performance plastics often filled with glass fiber reinforcements and additives like flame retardants. This matrix- based microstructure is designed to achieve a high-gloss surface by only a few polishing steps, dramatically reducing the tool lead time and enabling production of top quality plastic parts. Uddeholm Tyrax ESR can achieve a high hardness (up to 58 HRC) and is a suitable upgrade from AISI 420 ESR, AISI S7 and AISI 440C. Benefits good dimensional stability at heat treatment and in service even microstructure and small grain size good hardenability Uddeholm Tyrax is also available for Additive Manufacturing, powder for processing Laser Powder Bed Fusion (LPBF) and Laser Metal Deposition (LMD).
Read MoreFields marked with * are mandatory.