Plastic Extrusion

BÖHLER M303 is a corrosion-resistant, martensitic chromium steel with very good toughness, corrosion resistance, good wear resistance and improved machinability and polishability. Compared to 1.2316, BÖHLER M303 has better homogeneity and is approved for food and beverage contact.

BÖHLER M303 ISOPLAST corresponds to a remelted BÖHLER M303 . The variation in the production route enables greater toughness and polishability thanks to higher purity and improved homogeneity. Also available as product variant BÖHLER M303HH ISOPLAST (high-hard variant).

BÖHLER M310 ISOPLAST is a corrosion-resistant, martensitic chromium steel which, through electroslag remelting and optimization of the chemical composition, has a good homogeneity and a balanced hardness-toughness-corrosion resistance ratio.

BÖHLER M315 is a prehardened, corrosion-resistant martensitic plastic mold steel. Due to its chemical composition, BÖHLER M315 has improved machinability compared to 1.2085 and is approved for food contact.

BÖHLER M333 ISOPLAST is a corrosion-resistant, martensitic plastic mold steel with excellent polishability and toughness for products with highest surface requirements. BÖHLER M333 ISOPLAST is also approved for food and beverage contact.

BÖHLER M340 ISOPLAST corresponds to a corrosion-resistant, martensitic chromium steel with improved wear resistance. This is ideal for the application area of glass fiber reinforced plastics. In addition, the BÖHLER M340 ISOPLAST is approved for food and beverage contact.

BÖHLER M368 MICROCLEAN is a corrosion-resistant, martensitic chromium steel produced by powder metallurgy. Due to the alloy concept and the production route, the steel has a high wear resistance, high corrosion resistance and high toughness. In addition, BÖHLER M368 MICROCLEAN is approved for food and beverage contact.

BÖHLER M380 ISOPLAST is a high-nitrogen alloyed, corrosion-resistant, martensitic plastic mold steel electro-slag remelted under pressure with excellent corrosion resistance, very good polishability and very high toughness combined with a high hardness of up to 60 HRC. In addition, BÖHLER M380 ISOPLAST is approved for contact with food and beverage.

BÖHLER M390 MICROCLEAN is a corrosion-resistant, martensitic chromium steel produced by powder metallurgy. Due to its alloy design, this steel has very high wear resistance and good corrosion resistance. In addition, BÖHLER M390 MICROCLEAN is approved for food and beverage contact.

BÖHLER M398 MICROCLEAN is a corrosion-resistant, martensitic chromium steel produced by powder metallurgy. Due to its alloy design, this steel has good corrosion resistance and higher wear resistance compared to BÖHLER M390 MICROCLEAN.

BÖHLER M789 AMPO is a newly developed maraging steel, which combines the mechanical properties of 1.2709 with the corrosion resistance of 17-4PH. This patent bending grade can easily printed without any preheating and achieves a hardness of about 52 HRC with a very easy heat treatment. Furthermore, this material shows an excellent polishability, which makes it the ideal choice for inserts with conformal cooling in plastic injection molding and in any other application where a high hardness and corrosion resistance is of need.

Uddeholm Corrax is a precipitation hardening steel with a unique set of properties that makes it perfect for many demanding applications. The superior resistance against corrosion combined with a hardness up to 50 HRC and a simple heat treatment makes Uddeholm Corrax the obvious choice for long run series of aggressive plastics such as PVC. The chemical composition makes Uddeholm Corrax easy to process by Additive Manufacturing. Hence, it is also available as powder for Laser Powder Bed Fusion (LPBF) and Laser Metal Deposition (LMD). Benefits Very good corrosion resistance Flexible hardness of 34-50 HRC achieved by ageing No hard “white layer” after EDM

Uddeholm Elmax Super Clean is a powder metallurgically produced mould steel characterized by a combination of very good wear resistance, corrosion resistance and dimensional stability. Recommended for long production runs of smaller and complicated shapes and/or reinforced plastics. High wear resistance is normally connected to low corrosion resistance and vice versa. In Uddeholm Elmax SuperClean it has however been able to achieve this unique combination of properties by a powder-metallurgy-based production. Uddeholm Elmax SuperClean offers a possibility to make long-life, low maintenance moulds for the best overall moulding economy. Benefits Less wear because of god wear resistance Less indentations because of compressive strength Less maintenance because of corrosion resistance Less adjustments after heat treatment because of good dimensional stability Standard specification AFNOR Z170 CVD 17.3

Uddeholm Impax Supreme is prehardened mould steel with very good polishing and photo etching properties. It is suitable for a wide range of injection moulds, blow moulds and extrusion dies for plastic. Uddeholm Impax Supreme is supplied at 290-330 HB. In east/south east asian countries served by Assab Uddeholm Impax Supreme is sold as AS 718 Supreme. Benefits No hardening risks No hardening costs Time saving, e.g. no waiting for heat treatment Lower tool cost (e.g. no distortion to rectify) Modifications easily carried out Can be subsequently nitrided to increase surface wear resistance or locally flame hardened to reduce surface damage. Standard specification W.nr 1.2738 / AISI P20 / AFNOR 35 CND 7

Uddeholm Mirrax 40 is a prehardened remelted stainless tool steel, supplied at 40 HRC. Uddeholm Mirrax 40 is produced using the electroslag remelting (ESR) process – an additional step in the steelmaking process that ensures very clean steel. Consequently, Uddeholm Mirrax 40 is capable of being polished to a very high surface finish. In addition, the combination of high hardness with high toughness results in a mould with good resistance to indentations and minimize the risk of unexpected failures, leading to a safer mould and a prolonged tool life. Benefits Lower production costs Fast tool making Excellent surface finish possible Less maintenance work Safe production

Uddeholm Mirrax ESR is a through hardening corrosion resistant steel with very good polishability. Mainly intended for medium to large cross sections. It has a unique combination of toughness, corrosion resistance and through hardening properties. Benefits Low mould maintenance costs: The surface of cavity impressions retain their original finish over extended running periods. Moulds stored or operated in humid conditions require less protection. Low production costs: Water cooling channels are less affected by corrosion Heat transfer characteristics, and therefore cooling efficiency, are constant throughout the mould life, ensuring consistent cycle times. Safe mould use because of good toughness also in big dimensions

Uddeholm Nimax is a low carbon steel with excellent toughness, machinability and weldability. It has also good polishing and etching properties. Uddeholm Nimax combines high hardness with a high toughness. This leads to a mould with good resistance to indentations and a minimum risk for unexpected failures, thereby leading to a more reliable tool and prolonged tool life. Benefits Excellent machinability reduces the manufacturing time Easy weldability, as no preheating or post treatment necessary, Good resistance to indentations and a minimum risk for unexpected failures, because of the high hardness in combination with a high toughness Safe mould and aprolonged tool life Uddeholm Nimax delivery hardness is 360-400 HB.

Uddeholm Ramax HH is a corrosion resistant holder steel with good machinability, supplied in a high prehardened condition. Good machinability and corrosion resistance reduces tool manufacturing and maintenance costs. Benefits Low mould production cost thanks to low wear of the cutting edges in the milling and drilling operations and shorter machining time thanks to increased cutting speed possible. Lower mould maintenance costs due to corrosion resistance Lower production costs since water cooling channels are less effected by corrosion, ensuring consistent cycle time Uddeholm Ramax HH is supplied at a hardness level that is higher than other corrosion resistant prehardened grades, resulting in a more durable mould and a longer life time. By combining Uddeholm Ramax HH with one of our other products within the Stainless Concept, you can create a completely stainless mould.

Uddeholm Stavax ESR is a premium stainless mould steel for small and medium inserts and cores. Uddeholm Stavax ESR combines corrosion and wear resistance with excellent polishability, good machinability and stability in hardening. Mould maintenance requirement is reduced by assuring that core and cavity surfaces retain their original finish over extended operating periods. When compared with non stainless mould steel, Uddeholm Stavax ESR offers lower production costs by maintaining rust free cooling channels, assuring consistent cooling and cycle time. This classic stainless tool steel is the right choice when rust in production is unacceptable and where requirements for good hygiene are high, as within the medical industry, optical industry and for other high quality transparent parts. Uddeholm Stavax ESR is a part of the Uddeholm Stainless Concept. Benefits Low mould maintenance because of corrosion resistance: Surfaces retain their original finish Less production during storing and operation in humid condition Lower production costs: Since water-cooling channels are unaffected by corrosion Heat transfer characteristics, and therefore cooling efficiency, are constant throughout the mould life, ensuring consistent cycle times. Long life mould Standard specification W.nr 1.2083 / AISI 420 / AFNOR Z40 CV 14 (RSL)

Uddeholm Tyrax ESR combines best in class toughness, corrosion and wear resistance. This grade was developed for molding of high performance plastics often filled with glass fiber reinforcements and additives like flame retardants. This matrix- based microstructure is designed to achieve a high-gloss surface by only a few polishing steps, dramatically reducing the tool lead time and enabling production of top quality plastic parts. Uddeholm Tyrax ESR can achieve a high hardness (up to 58 HRC) and is a suitable upgrade from AISI 420 ESR, AISI S7 and AISI 440C. Benefits good dimensional stability at heat treatment and in service even microstructure and small grain size good hardenability Uddeholm Tyrax is also available for Additive Manufacturing, powder for processing Laser Powder Bed Fusion (LPBF) and Laser Metal Deposition (LMD).

Uddeholm Vanax SuperClean is the long-awaited response to the market’s need for steel that is both strong and stainless. Combining the corrosion resistance of austenitic stainless steel such as AISI 316L, with a hardness of 60 HRC and the wear resistance of a cold work tool steel, opens up new opportunities. Where no previous materials suffice, this powder metallurgical steel grade offers resistance in the most corrosive environments possible. From start to finish, its unique material properties provide reliable performance in the most extreme conditions and for the most demanding working materials. Benefits Uddeholm Vanax SuperClean has an excellent corrosion resistance both in low and high temperature tempered condition in combination with good wear resistance to counteract mixed wear/galling/fretting. Applications are e.g. found in plastic moulding, food processing and engineering designs.