Blow Moulding

BÖHLER M303 is a corrosion-resistant, martensitic chromium steel with very good toughness, corrosion resistance, good wear resistance and improved machinability and polishability. Compared to 1.2316, BÖHLER M303 has better homogeneity and is approved for food and beverage contact.

BÖHLER M303 ISOPLAST corresponds to a remelted BÖHLER M303 . The variation in the production route enables greater toughness and polishability thanks to higher purity and improved homogeneity. Also available as product variant BÖHLER M303HH ISOPLAST (high-hard variant).

BÖHLER M310 ISOPLAST is a corrosion-resistant, martensitic chromium steel which, through electroslag remelting and optimization of the chemical composition, has a good homogeneity and a balanced hardness-toughness-corrosion resistance ratio.

BÖHLER M315 is a prehardened, corrosion-resistant martensitic plastic mold steel. Due to its chemical composition, BÖHLER M315 has improved machinability compared to 1.2085 and is approved for food contact.

BÖHLER M333 ISOPLAST is a corrosion-resistant, martensitic plastic mold steel with excellent polishability and toughness for products with highest surface requirements. BÖHLER M333 ISOPLAST is also approved for food and beverage contact.

BÖHLER W300 ISOBLOC is a 5% chromium steel and corresponds to material number 1.2343 (X37CrMoV5-1). Produced via the electroslag remelting process (ESR), this tool steel has very high hot toughness as well as good hot hardness and very good resistance against heat-checkings. The combination of these properties makes it a top performer in high- and low-pressure die casting as well as in closed-die and open-die forging. In addition, this material has very good polishability and is therefore also often used as a molding material for plastic injection molds.

BÖHLER W302 ISOBLOC is a 5% chromium steel and corresponds to material number 1.2344 (X40CrMoV5-1). Produced via the electroslag remelting process (ESR), this tool steel has very high hot toughness as well as very high hot hardness and a very good resistance against heat-checkings. The combination of these properties makes it a top performer in closed- and open-die forging as well as in high- and low-pressure die casting. In addition, this material has very good polishability and is therefore also often used as a molding material for plastic injection molds.

BÖHLER W302 ISODISC is a 5% chromium steel and corresponds to material number 1.2344 (X40CrMoV5-1). This common tool steel has good hot toughness as well as a high hot hardness and a high resistance against heat-checkings. The combination of these properties makes it a standard choice in extrusion, forging and low-pressure die casting. This material is also available as W302 ISOBLOC which is a remelted grade with improved cleanliness, homogeneity and toughness.

Uddeholm Corrax is a precipitation hardening steel with a unique set of properties that makes it perfect for many demanding applications. The superior resistance against corrosion combined with a hardness up to 50 HRC and a simple heat treatment makes Uddeholm Corrax the obvious choice for long run series of aggressive plastics such as PVC. The chemical composition makes Uddeholm Corrax easy to process by Additive Manufacturing. Hence, it is also available as powder for Laser Powder Bed Fusion (LPBF) and Laser Metal Deposition (LMD). Benefits Very good corrosion resistance Flexible hardness of 34-50 HRC achieved by ageing No hard “white layer” after EDM

Uddeholm Impax Supreme is prehardened mould steel with very good polishing and photo etching properties. It is suitable for a wide range of injection moulds, blow moulds and extrusion dies for plastic. Uddeholm Impax Supreme is supplied at 290-330 HB. In east/south east asian countries served by Assab Uddeholm Impax Supreme is sold as AS 718 Supreme. Benefits No hardening risks No hardening costs Time saving, e.g. no waiting for heat treatment Lower tool cost (e.g. no distortion to rectify) Modifications easily carried out Can be subsequently nitrided to increase surface wear resistance or locally flame hardened to reduce surface damage. Standard specification W.nr 1.2738 / AISI P20 / AFNOR 35 CND 7

Uddeholm Mirrax 40 is a prehardened remelted stainless tool steel, supplied at 40 HRC. Uddeholm Mirrax 40 is produced using the electroslag remelting (ESR) process – an additional step in the steelmaking process that ensures very clean steel. Consequently, Uddeholm Mirrax 40 is capable of being polished to a very high surface finish. In addition, the combination of high hardness with high toughness results in a mould with good resistance to indentations and minimize the risk of unexpected failures, leading to a safer mould and a prolonged tool life. Benefits Lower production costs Fast tool making Excellent surface finish possible Less maintenance work Safe production

Uddeholm Mirrax ESR is a through hardening corrosion resistant steel with very good polishability. Mainly intended for medium to large cross sections. It has a unique combination of toughness, corrosion resistance and through hardening properties. Benefits Low mould maintenance costs: The surface of cavity impressions retain their original finish over extended running periods. Moulds stored or operated in humid conditions require less protection. Low production costs: Water cooling channels are less affected by corrosion Heat transfer characteristics, and therefore cooling efficiency, are constant throughout the mould life, ensuring consistent cycle times. Safe mould use because of good toughness also in big dimensions

Uddeholm Nimax is a low carbon steel with excellent toughness, machinability and weldability. It has also good polishing and etching properties. Uddeholm Nimax combines high hardness with a high toughness. This leads to a mould with good resistance to indentations and a minimum risk for unexpected failures, thereby leading to a more reliable tool and prolonged tool life. Benefits Excellent machinability reduces the manufacturing time Easy weldability, as no preheating or post treatment necessary, Good resistance to indentations and a minimum risk for unexpected failures, because of the high hardness in combination with a high toughness Safe mould and aprolonged tool life Uddeholm Nimax delivery hardness is 360-400 HB.

Uddeholm Nimax ESR is an ESR remelted version of Uddeholm Nimax, keeping the features of Uddeholm Nimax, but with improved cleanliness and homogeneity as a result of the ESR process. Benefits Excellent polishing and etching properties Excellent machinability reduces the manufacturing time Easy weldability, as no preheating or post treatment necessary Good resistance to indentations and a minimum risk for unexpected failures, because of the high hardness in combination with a high toughness Safe mould and a prolonged tool life Examples of applications for Uddeholm Nimax ESR Automotive: Head and rear light, Large interior parts White goods: Control panels Electronic: LED TV frames

Uddeholm Ramax HH is a corrosion resistant holder steel with good machinability, supplied in a high prehardened condition. Good machinability and corrosion resistance reduces tool manufacturing and maintenance costs. Benefits Low mould production cost thanks to low wear of the cutting edges in the milling and drilling operations and shorter machining time thanks to increased cutting speed possible. Lower mould maintenance costs due to corrosion resistance Lower production costs since water cooling channels are less effected by corrosion, ensuring consistent cycle time Uddeholm Ramax HH is supplied at a hardness level that is higher than other corrosion resistant prehardened grades, resulting in a more durable mould and a longer life time. By combining Uddeholm Ramax HH with one of our other products within the Stainless Concept, you can create a completely stainless mould.

Uddeholm Stavax ESR is a premium stainless mould steel for small and medium inserts and cores. Uddeholm Stavax ESR combines corrosion and wear resistance with excellent polishability, good machinability and stability in hardening. Mould maintenance requirement is reduced by assuring that core and cavity surfaces retain their original finish over extended operating periods. When compared with non stainless mould steel, Uddeholm Stavax ESR offers lower production costs by maintaining rust free cooling channels, assuring consistent cooling and cycle time. This classic stainless tool steel is the right choice when rust in production is unacceptable and where requirements for good hygiene are high, as within the medical industry, optical industry and for other high quality transparent parts. Uddeholm Stavax ESR is a part of the Uddeholm Stainless Concept. Benefits Low mould maintenance because of corrosion resistance: Surfaces retain their original finish Less production during storing and operation in humid condition Lower production costs: Since water-cooling channels are unaffected by corrosion Heat transfer characteristics, and therefore cooling efficiency, are constant throughout the mould life, ensuring consistent cycle times. Long life mould Standard specification W.nr 1.2083 / AISI 420 / AFNOR Z40 CV 14 (RSL)