Fasteners in energy applications require high‑strength BÖHLER steels with excellent fatigue and corrosion resistance. Key quality features include ultra‑clean materials, full traceability, controlled heat treatment, and rigorous testing for safe, reliable performance.
Fasteners such as bolts and nuts used in energy applications are critical safety components exposed to high loads, temperature fluctuations, and often corrosive environments such as offshore, hydrogen, or power generation systems. Material requirements focus on high tensile strength, fatigue resistance, creep performance, and resistance to stress corrosion cracking and hydrogen embrittlement. Stability of mechanical properties over long service intervals is essential to ensure safe operation and prevent failure under dynamic loading conditions.
BÖHLER high‑performance steels and alloys are specifically designed to meet these demanding requirements. Advanced quenched and tempered steels, martensitic and precipitation‑hardened stainless steels, as well as corrosion‑resistant alloy grades provide optimized combinations of strength, toughness, and environmental resistance. Produced via advanced melting technologies, BÖHLER materials offer superior cleanliness and controlled microstructure, supporting extended fatigue life. Key quality features include strict chemical composition control, certified traceability, and validated heat treatment processes. Comprehensive non‑destructive testing, mechanical testing, and dimensional inspection ensure consistent quality. BÖHLER solutions enable reliable fastening systems, improved safety margins, and long‑term performance in demanding energy applications.
BÖHLER N700 is a corrosion-resistant steel in the form of bars, wire and forgings in the solution-annealed condition. It is a martensitic, precipitation-hardenable chromium-nickel-copper steel with high strength and toughness. Further increases in strength can be achieved by cold forming and subsequent precipitation hardening. These products are typically used for parts that require higher corrosion resistance than the usual 13% or 17% chromium steels and high strength up to 316 °C. However, their use is not limited to such applications. Remelting processes are used to improve steel purity and homogeneity. (ESR, PESR, VAR) Certain processing methods and operating conditions can make these products susceptible to stress corrosion cracking. For applications such as bolting where stress corrosion cracking is possible, the product should be aged for at least 4 hours at the highest temperature compatible with the strength requirements, but in no case lower than 552 °C. Typical applications for reactor construction and highly stressed pump parts, springs and ship shafts.
Read MoreBÖHLER W300 ISOBLOC is a 5% chromium steel and corresponds to material number 1.2343 (X37CrMoV5-1). Produced via the electroslag remelting process (ESR), this tool steel has very high hot toughness as well as good hot hardness and very good resistance against heat-checkings. The combination of these properties makes it a top performer in high- and low-pressure die casting as well as in closed-die and open-die forging. In addition, this material has very good polishability and is therefore also often used as a molding material for plastic injection molds.
Read MoreBÖHLER W300 ISODISC is a 5% chromium steel and corresponds to material number 1.2343 (X37CrMoV5-1). This common tool steel has good hot toughness as well as a high hot hardness and a high resistance against heat-checkings. The combination of these properties makes it a standard choice in extrusion, forging and low-pressure die casting. This material is also available as W300 ISOBLOC which is a remelted grade with improved cleanliness, homogeneity and toughness.
Read MoreBÖHLER W302 ISOBLOC is a 5% chromium steel and corresponds to material number 1.2344 (X40CrMoV5-1). Produced via the electroslag remelting process (ESR), this tool steel has very high hot toughness as well as very high hot hardness and a very good resistance against heat-checkings. The combination of these properties makes it a top performer in closed- and open-die forging as well as in high- and low-pressure die casting. In addition, this material has very good polishability and is therefore also often used as a molding material for plastic injection molds.
Read MoreBÖHLER W360 ISOBLOC is a material produced by the electroslag remelting process (ESR), which has been specially adapted for use at high tool hardnesses in the range of 51-57 HRC. Although the steel can be classified as a 5% chromium steel, the increased carbon and molybdenum content coupled with state-of-the-art manufacturing technology ensures that BÖHLER W360 ISOBLOC still shows a very good toughness and an exceptionally good thermal resistance, even at high hardness levels. These properties make the steel the perfect choice for smaller components in the die casting sector (e.g., mold inserts, cores, core pins, ejector pins, etc.). The material also is frequently the preferred choice for closed-die and open-die forging tools due to its high wear resistance. Because of this excellent wear resistance and the high toughness, BÖHLER W360 ISOBLOC is also frequently used for cold work applications and as a molding material for plastic injection molds. The Steel also is available as powder material for metal-3D-printing under the brand name BÖHLER W360 AMPO.
Read MoreBÖHLER W720 VMR is not a classic hot work tool steel, but an ultra-high strength maraging steel. Compared to quenched and tempered steels, the material generates its high strength not through a hardened and tempered martensitic structure with a high carbon content and secondary hardening carbides, but through the precipitation of intermetallic phases from a tough nickel martensitic matrix. BÖHLER W720 VMR corresponds to material number 1.6358 (X2NiCoMoTi18-9-5) and has proven to be ideally suited for many tool steel applications in cold and hot work (e.g., for extrusion stems) up to 450 °C.
Read More