Hot Runners

BÖHLER M238 is a prehardened, non-corrosion-resistant plastic mould steel with good machinability. The addition of Ni guarantees uniform strength across the entire cross-section, even with large dimensions (up to 600 mm).

BÖHLER M303 is a corrosion-resistant, martensitic chromium steel with very good toughness, corrosion resistance, good wear resistance and improved machinability and polishability. Compared to 1.2316, BÖHLER M303 has better homogeneity and is approved for food and beverage contact.

BÖHLER M303 ISOPLAST corresponds to a remelted BÖHLER M303 . The variation in the production route enables greater toughness and polishability thanks to higher purity and improved homogeneity. Also available as product variant BÖHLER M303HH ISOPLAST (high-hard variant).

BÖHLER M310 ISOPLAST is a corrosion-resistant, martensitic chromium steel which, through electroslag remelting and optimization of the chemical composition, has a good homogeneity and a balanced hardness-toughness-corrosion resistance ratio.

BÖHLER M333 ISOPLAST is a corrosion-resistant, martensitic plastic mold steel with excellent polishability and toughness for products with highest surface requirements. BÖHLER M333 ISOPLAST is also approved for food and beverage contact.

BÖHLER M789 AMPO is a newly developed maraging steel, which combines the mechanical properties of 1.2709 with the corrosion resistance of 17-4PH. This patent bending grade can easily printed without any preheating and achieves a hardness of about 52 HRC with a very easy heat treatment. Furthermore, this material shows an excellent polishability, which makes it the ideal choice for inserts with conformal cooling in plastic injection molding and in any other application where a high hardness and corrosion resistance is of need.

BÖHLER W300 ISOBLOC is a 5% chromium steel and corresponds to material number 1.2343 (X37CrMoV5-1). Produced via the electroslag remelting process (ESR), this tool steel has very high hot toughness as well as good hot hardness and very good resistance against heat-checkings. The combination of these properties makes it a top performer in high- and low-pressure die casting as well as in closed-die and open-die forging. In addition, this material has very good polishability and is therefore also often used as a molding material for plastic injection molds.

BÖHLER W300 ISODISC is a 5% chromium steel and corresponds to material number 1.2343 (X37CrMoV5-1). This common tool steel has good hot toughness as well as a high hot hardness and a high resistance against heat-checkings. The combination of these properties makes it a standard choice in extrusion, forging and low-pressure die casting. This material is also available as W300 ISOBLOC which is a remelted grade with improved cleanliness, homogeneity and toughness.

BÖHLER W302 ISOBLOC is a 5% chromium steel and corresponds to material number 1.2344 (X40CrMoV5-1). Produced via the electroslag remelting process (ESR), this tool steel has very high hot toughness as well as very high hot hardness and a very good resistance against heat-checkings. The combination of these properties makes it a top performer in closed- and open-die forging as well as in high- and low-pressure die casting. In addition, this material has very good polishability and is therefore also often used as a molding material for plastic injection molds.

Uddeholm Elmax Super Clean is a powder metallurgically produced mould steel characterized by a combination of very good wear resistance, corrosion resistance and dimensional stability. Recommended for long production runs of smaller and complicated shapes and/or reinforced plastics. High wear resistance is normally connected to low corrosion resistance and vice versa. In Uddeholm Elmax SuperClean it has however been able to achieve this unique combination of properties by a powder-metallurgy-based production. Uddeholm Elmax SuperClean offers a possibility to make long-life, low maintenance moulds for the best overall moulding economy. Benefits Less wear because of god wear resistance Less indentations because of compressive strength Less maintenance because of corrosion resistance Less adjustments after heat treatment because of good dimensional stability Standard specification AFNOR Z170 CVD 17.3

Uddeholm Mirrax 40 is a prehardened remelted stainless tool steel, supplied at 40 HRC. Uddeholm Mirrax 40 is produced using the electroslag remelting (ESR) process – an additional step in the steelmaking process that ensures very clean steel. Consequently, Uddeholm Mirrax 40 is capable of being polished to a very high surface finish. In addition, the combination of high hardness with high toughness results in a mould with good resistance to indentations and minimize the risk of unexpected failures, leading to a safer mould and a prolonged tool life. Benefits Lower production costs Fast tool making Excellent surface finish possible Less maintenance work Safe production

Uddeholm Mirrax ESR is a through hardening corrosion resistant steel with very good polishability. Mainly intended for medium to large cross sections. It has a unique combination of toughness, corrosion resistance and through hardening properties. Benefits Low mould maintenance costs: The surface of cavity impressions retain their original finish over extended running periods. Moulds stored or operated in humid conditions require less protection. Low production costs: Water cooling channels are less affected by corrosion Heat transfer characteristics, and therefore cooling efficiency, are constant throughout the mould life, ensuring consistent cycle times. Safe mould use because of good toughness also in big dimensions

Uddeholm Orvar Supreme can be regarded as an “all-round” steel used in several application areas. Except for hot work application areas the steel is also used in moulds for plastics and as a material in high stressed axles. The high degree of purity and the very fine structure shows improvement in dies and components where high mechanical and thermal stresses are involved. Uddeholm Orvar Supreme is produced using the Electro-Slag-Refining (ESR) technique. The ESR process gives Uddeholm Orvar Supreme a high level of homogeneity and cleanliness which results in a high performance hot work tool steel of the highest quality. Benefits Improved tooling performance Uddeholm Orvar Supreme meets the North American Die Casting Association (NADCA) #207 requirements for Superior high quality H-13 die steel. Standard specification W.nr 1.2344 / AISI H13 / AFNOR Z38 CDV 5.1

Uddeholm Stavax ESR is a premium stainless mould steel for small and medium inserts and cores. Uddeholm Stavax ESR combines corrosion and wear resistance with excellent polishability, good machinability and stability in hardening. Mould maintenance requirement is reduced by assuring that core and cavity surfaces retain their original finish over extended operating periods. When compared with non stainless mould steel, Uddeholm Stavax ESR offers lower production costs by maintaining rust free cooling channels, assuring consistent cooling and cycle time. This classic stainless tool steel is the right choice when rust in production is unacceptable and where requirements for good hygiene are high, as within the medical industry, optical industry and for other high quality transparent parts. Uddeholm Stavax ESR is a part of the Uddeholm Stainless Concept. Benefits Low mould maintenance because of corrosion resistance: Surfaces retain their original finish Less production during storing and operation in humid condition Lower production costs: Since water-cooling channels are unaffected by corrosion Heat transfer characteristics, and therefore cooling efficiency, are constant throughout the mould life, ensuring consistent cycle times. Long life mould Standard specification W.nr 1.2083 / AISI 420 / AFNOR Z40 CV 14 (RSL)

Uddeholm Tyrax ESR combines best in class toughness, corrosion and wear resistance. This grade was developed for molding of high performance plastics often filled with glass fiber reinforcements and additives like flame retardants. This matrix- based microstructure is designed to achieve a high-gloss surface by only a few polishing steps, dramatically reducing the tool lead time and enabling production of top quality plastic parts. Uddeholm Tyrax ESR can achieve a high hardness (up to 58 HRC) and is a suitable upgrade from AISI 420 ESR, AISI S7 and AISI 440C. Benefits good dimensional stability at heat treatment and in service even microstructure and small grain size good hardenability Uddeholm Tyrax is also available for Additive Manufacturing, powder for processing Laser Powder Bed Fusion (LPBF) and Laser Metal Deposition (LMD).