Letecké součásti vyžadují vysoce čisté oceli a slitiny s vynikající pevností, odolností proti únavě a stabilitou. Mezi klíčové kvalitativní znaky patří certifikované materiály, úplná sledovatelnost, kontrolované tepelné zpracování, nedestruktivní zkoušení a soulad s leteckými normami.
Letecké součásti jsou navrhovány pro provoz v mimořádně náročných podmínkách, kde jsou bezpečnost, spolehlivost a výkon rozhodujícími požadavky. Požadavky na materiály vycházejí z extrémních mechanických zatížení, širokého teplotního rozsahu, únavového namáhání a v mnoha případech také z korozivního prostředí. Oceli a pokročilé slitiny používané v letectví musí vykazovat vysoký poměr pevnosti k hmotnosti, vynikající odolnost proti únavě, vysokou lomovou houževnatost a dlouhodobou rozměrovou stabilitu. Metalurgická čistota a řízená mikrostruktura jsou nezbytné pro zabránění předčasnému selhání. Mezi běžně používané materiály patří vysokopevnostní nízkolegované oceli, martenzitické a precipitačně vytvrzované korozivzdorné oceli a letecké jakosti vyráběné vakuovým přetavením pro minimalizaci obsahu vměstků. Slitiny na bázi niklu a titanu se používají tam, kde jsou vyžadovány vysokoteplotní vlastnosti a snížení hmotnosti. Kvalitativní požadavky jsou definovány leteckými normami a zahrnují úplnou sledovatelnost materiálů, certifikované chemické složení, validované tepelné zpracování a přísné řízení procesů. Nedestruktivní zkoušení, rozměrové kontroly a inspekce integrity povrchu jsou standardními opatřeními zajišťujícími shodu s požadavky, opakovatelnost výroby a bezpečný provoz po celou dobu životnosti součásti.
BÖHLER L531 is the classic Ti-6Al-4V alloy and therefore the most common Titanium alloy with a wide range of applications.
Číst víceBohler L533 is the „Extra Low Interstitials“ version of the classic Ti-6Al-4V alloy with special high purity and lower content of oxygen and iron.
Číst víceBÖHLER L625 is a non-magnetizable corrosion and heat resistant nickel alloy in the form of bars, forgings and semi-finished products up to max 254 mm diameter/ cross-section and oxidation resistant up to 1093°C. Best fatigue strength and resistance to stress corrosion cracking when exposed to chloride containing media. Good weldability.
Číst víceBÖHLER L625 AMPO je nemagnetická slitina odolná vůči korozi a tvorbě okují na bázi niklu. Vysoká houževnatost a pevnost od nejnižších teplot až do 1 000 °C. Snadný tisk.
Číst víceBÖHLER L718 AMPO je tvrditelná super slitina na základě niklu. Tento vysoce tepelně odolný materiál vykazuje dobré pevnostní vlastnosti za zvýšených teplot až do 750 °C, i vynikající odolnost vůči tečení až do 700 ° C. Navíc vykazuje vynikající odolnost vůči korozi a snadný tisku. U tištěných dílů vyrobených z tohoto prášku lze dosáhnout v podstatě stejných vlastností jako u tyčového materiálu.
Číst víceBÖHLER L718AMS is a corrosion and heat resistant nickel alloy – precipitation hardenable – in the form of bars, forging and forging stock. High resistance to creep and stress-rupture up to 1300°F (704°C) and oxidation resistance up to 1800°F (982°C). High duty parts and components for oil & gas and CPI applications, components for automotive, gas turbines, aerospace engines, high-speed airframe parts such as disks, buckets, spacers and high temperature bolts and fasteners.
Číst víceBÖHLER L718HCB is a corrosion and heat resistant nickel alloy – precipitation hardenable – in the form of bars, forging and forging stock. High resistance to creep and stress-rupture up to 1300°F (704°C) and oxidation resistance up to 1800°F (982°C). High duty parts and components for gas turbines, aerospace engines, high-speed airframe parts such as disks, buckets, spacers and high temperature bolts and fasteners. Compared to standard alloy 718 AMS limits, Cb in L718HCb is adjusted in the upper range of the standard limits in order to enhance mechanical properties. L718HCb is typically used for high temperature bolting and fasteners.
Číst víceBÖHLER LHX is a corrosion and heat resistant nickel alloy in the form of bars, forging and forging stock. Resistant to oxidation up to 2200°F (1204°C) and high strength above 1500°F (816°C). It is widely used typically for parts, in engines especially for combustion chambers, after burners and exhaust components but usage is not limited to such applications.
Číst víceBÖHLER N352 is a martensitic chromium steel with nickel addition. Heat treatable grade, capable of taking a mirror finish. Higher corrosion resistance compared to 13% chromium steal. Resistant to the effects of seawater, weak acids and alkaline solutions, as well as to acids having a strong, oxidizing effect such as nitric acid. Surface finish for optimum corrosion resistance: fine ground or polished. For components subject to high mechanical and corrosive stress, e.g. screws and shafts, at operating temperatures up to approx. 752° F.
Číst víceBÖHLER N360 is a premium aircraft quality corrosion resistant, martensitic stainless steel, produced using the P-ESR-process. Compared to conventionally produced Cr and CrMo steels, BÖHLER N360 offers improved corrosion resistance and toughness properties as well as high hardness and compressive strength. It is typically used for anti-friction bearing components e.g. bearings, ball screws and wear resistant components for use in the aircraft industry and for automotive components, requiring resistance to both corrosion and wear with hardness not lower than 58 HRC after hardening and tempering, but usage is not limited to such applications.
Číst víceBÖHLER N695 is a Chromium alloyed stainless steel with high hardness, wear resistance and good corrosion resistance in the hardened and tempered condition. this grade is typically used for parts requiring hardness up to 58 HRC and resistance to wear, corrosion, and oxidation, e.g. balls, rollers, needles and rings for corrosion resistant bearings, but usage is not limited to such applications.
Číst víceBÖHLER N695SA is a high-grade, vacuum remelted chromium stainless steel of aerospace quality, offering high hardness, wear resistance, and good corrosion resistance in the quenched and tempered condition. Compared to air-melted quality, this steel exhibits improved rolling contact fatigue properties and is typically used for components requiring hardness up to 58 HRC and resistance to wear, corrosion, and oxidation—such as balls, rollers, needles, and rings for corrosion-resistant bearings—although its use is not limited to these applications.
Číst víceBÖHLER N700 is a high-quality corrosion-resistant steel in aerospace quality, in the form of bars, wire and forgings with a diameter/thickness of up to 203 mm in the solution-annealed condition, as well as starting material of any size for forging purposes. It is a martensitic, precipitation-hardenable chromium-nickel-copper steel with high strength and toughness. Further increases in strength can be achieved by cold forming and subsequent precipitation hardening. These products are typically used for parts requiring corrosion resistance and high strength up to 316°C. However, their use is not limited to such applications. However, use is not limited to such applications. Certain processing methods and operating conditions can cause these products to become susceptible to stress corrosion cracking. For applications such as bolting where stress corrosion cracking is possible, the product should be aged for a minimum of 4 hours at the highest temperature compatible with the strength requirements, but in no case lower than 552°C.
Číst víceBÖHLER N700 AMPO (17-4 PH) je niklová martenzitická ocel s vytvrzováním srážením. Díky kombinaci legur má tento materiál vynikající odolnost vůči korozi. Lze jej velmi snadno tisknout bez dodatečného předehřevu a po rozpouštěcím žíhání a stárnutí dosahuje tvrdosti přibližně 40 HRC.
Číst víceBÖHLER N701 is a high quality, vacuum remelted, corrosion resistant steel for aerospace applications in the form of bars for machining up to 200 mm in diameter. It is a martensitic, precipitation hardenable chromium-nickel-copper steel with high strength and toughness. These products are typically used for parts that require corrosion resistance, high strength up to 600 °F, and exhibit good toughness & strength in the transverse direction of large dimensions. However, use is not limited to such applications. Certain processing methods and operating conditions can cause these products to become susceptible to Stress corrosion cracking.
Číst víceBÖHLER N701 AMS is a premium, aerospace-quality corrosion-resistant steel available in bars, wire, and forgings with diameters/thicknesses up to 203 mm in the solution-annealed condition, as well as pre-forging stock of any size. It is a martensitic, precipitation-hardenable chromium-nickel-copper steel with high strength and toughness. Further strength increases can be achieved through cold working and subsequent precipitation hardening. These products are typically used for parts requiring corrosion resistance and high strength up to 316 °C and must exhibit good transverse toughness and strength in large dimensions. However, their use is not limited to such applications. Certain processing methods and operating conditions can make these products susceptible to stress corrosion cracking.
Číst víceBÖHLER N709 is a premium aircraft-quality corrosion-resistant steel in the form of bars, wire, forgings up to 12.0 inches (305 mm) in diameter or least distance between parallel sides in the solution heat treated condition as well as stock of any size for forging. It is a martensitic precipitation hardenable chromium-nickel-molydenum-aluminium steel possessing high strength and toughness. These products have been used typically for parts requiring corrosion resistance, stress-corrosion resistance and high strength up to 600 °F (316 °C) with good ductility and strength in the transverse direction in large section sizes but,but usage is not limited to such applications. Certain processing procedures and service conditions may cause these products to become subject to stress-corrosion cracking.
Číst víceBÖHLER N717 is a premium quality, corrosion-resistant steel for aerospace applications, supplied in the form of bars, wire, forgings in the solution-annealed condition, and pre-material of any size for forging. It is a martensitic, precipitation-hardenable chromium-nickel-molybdenum-aluminum steel with high strength and toughness. This steel is typically used for components requiring corrosion resistance and a combination of high strength and toughness up to 427 °C, although its use is not limited to such applications. Certain processing methods and service conditions may lead to stress corrosion cracking in these products.
Číst víceTento materiál se díky dobré kombinaci vlastností, jako je dobrá tvářitelnost, vysoká pevnost a dobrá odolnost proti korozi, výborně hodí pro široké spektrum aplikací v leteckém a kosmickém průmyslu.
Číst víceBÖHLER R100 ia a a premium aircraft-quality, vacuum-arc-remelted low-alloy steel in the form of bars, forgings and forging stock. The grade is used typically for parts requiring through hardening properties, usually with hardness of approximately 60 HRC in section thicknesses 0.50 inch (12.7 mm) and under. E.g. bearing rings and rolling elements, bearing balls and races.
Číst víceBÖHLER R250 is a a premium aircraft-quality, double vacuum-melted low-alloy steel in the form of bars, forgings and forging stock. The grade is used typically for parts such as bearings operating under heavy loads and high speeds at moderate temperatures up to 600° F. E.g. bearings and rolling elements, bearing balls and races.
Číst více“This specification covers a corrosion and heat resistant steel in the form of bars, wire, forgings and forging stock. It is an austenitic, precipitation hardenable, iron-nickel-chromium-molydenum-titanium steel of ESR quality. Alloying elements of aluminium and titanium allow this material to undergo precipitation hardening (ageing) through the formation of intermetallic phases. The addition of molybdenum increases the mechanical properties and resistance to creep at high temperatures. These products have been typically used for parts in power generation engineering i.e. gas turbines requiring moderate strength up to 704 °C (1300 °F) and oxidation resistance up to 816 °C (1500 °F), but their use is not limited to such applications.”
Číst víceBÖHLER T550 – vysoce žárupevná ocel k zušlechťování. Obvyklá horní hranice teploty pro použití je 580 °C. Díly a komponenty s vyšší pevností za tepla pro tepelné stroje a zařízení s tepelnými stroji, jako např. lopatky a oběžná kola turbín, šrouby, čepy a hřídele.
Číst víceBÖHLER T552 is a premium aircraft-quality corrosion-resistant chromium-nickel-molydenum steel in the form of bars, wire, forgings and stock for forging. These products have been used typically for parts such as compressor wheels and structural members requiring corrosion resistance and high strength up to 800°F (427 °C), but usage is not limited to such applications.
Číst víceBÖHLER T670 is a corrosion-resistant steel for aerospace applications in the form of bars, wire, and forgings with diameters/thicknesses up to 305 mm in the solution-annealed condition, as well as pre-forging material of any size. It is a martensitic, precipitation-hardenable chromium-nickel-copper-molybdenum steel with high strength and toughness. BÖHLER T670 is primarily suitable for parts requiring corrosion resistance close to that of Cr-Ni 18-8 steels and exceeding the strength of martensitic 12% Cr steels. This steel can be processed in the solution-annealed condition and, through precipitation treatment, achieves tensile strengths of up to 1080 MPa with good ductility and strength in the transverse directions, even in large cross-sections. Certain processing methods and operating conditions can cause stress corrosion cracking in these products.
Číst víceBÖHLER V145 is a Cr-Ni-Mo- steel for applications requiring high tensile and toughness values, in particular in large cross sections in the quenched and tempered condition. The molybdenum addition prevents the steel from being susceptible to temper embrittlement. Highly stressed components with large cross sections for aircraft, such as gear shafts and landing gear components.
Číst víceBÖHLER V250 is a premium aircraft-quality, maraging alloy steel in the form of bars, forgings and stock for forging. In contrast to heat treatable steels its outstanding tensile properties are not due to a hardened structure with relatively high carbon content, but to precipitation of intermetallic phases from a ductile nickel bearing matrix containing almost no carbon. These products have been used typically for parts requiring through hardening, without quenching, to a minimum yield strength of 247 ksi (1700 MPa) and where such parts may require welding during fabrication, but usage is not limited to such applications. E.g highly stressed components for the aircraft and rocket industries.
Číst víceBÖHLER V250AMS is a premium aircraft-quality, maraging alloy steel in the form of bars, forgings and stock for forging up through 10 inches (254.00 mm) inclusive in diameter or least distance between parallel sides. In contrast to heat treatable steels its outstanding tensile properties are not due to a hardened structure with relatively high carbon content, but to precipitation of intermetallic phases from a ductile nickel bearing matrix containing almost no carbon. These products have been used typically for parts requiring through hardening, without quenching, to a minimum yield strength of 240 ksi (1655 MPa) and where such parts may require welding during fabrication, but usage is not limited to such applications. E.g highly stressed components for the aircraft and rocket industries.
Číst víceBÖHLER V300 covers a premium aircraft-quality, maraging alloy steel in the form of bars, forgings and stock for forging up through 10 inches (254.00 mm) inclusive in diameter or least distance between parallel sides. In contrast to heat treatable steels its outstanding tensile properties are not due to a hardened structure with relatively high carbon content, but to precipitation of intermetallic phases from a ductile nickel bearing matrix containing almost no carbon. These products have been used typically for parts requiring through hardening, without quenching, to a minimum yield strength of 270 ksi (1862 MPa) and where such parts may require welding during fabrication, but usage is not limited to such applications. E.g highly stressed components for the aircraft and rocket industries.
Číst víceBÖHLER V354 is an alloyed Cr-Mo-V quenched and tempered steel for high strength and high temperature requirements, good weldability and suitable for nitriding. Insensitive to tempering embrittlement due to Mo content. Mainly for components in the aerospace industry to be welded and nitrided with high quenched and tempered strength, at operating temperatures from -75° C to 500° C.
Číst víceBÖHLER V361 is a 3% Cr-Mo-V nitriding low-alloy steel of premium aircraft-quality, low-alloy steel offering a tensile strength of up to over 1350MPa in the form of bars, forgings, and forging stock. Due to the optimized production route via VIM-melting and VAR-remelting, the steel offers high impact strength and fatigue limit. It may be nitrided in the heat treated condition to obtain a wear resistant surface. It is used typically for nitrided parts such as bearings, operating under heavy loads and high speeds at moderate temperatures, and requiring highest surface hardness, high core toughness, and less distortion than parts made from case hardening steel, but usage is not limited to such applications.
Číst víceV případě Vašeho zájmu nás kontaktujte.